How To Repair Earphone Jack

Table of Contents

• What Tools practice Yous Need To Replace A Headphone Plug?
  • Before proceeding with the headphone plug replacement
  • Headphone Jack Parts
• Headphone Jack Replacement Steps
• Add – on Notation
• Conclusion

To replace a headphone plug you need the followings, and then yous may check their prices at Amazon:

1. New aux jack.
2. Wirecutter or Affluent Cutter.
3. Wire stripper.
4. Soldering Iron Tool.
5. Lighter.

Since this is the easy fashion to supersede a headphone plug, let'southward guide y'all through the procedure below.

Before proceeding with the headphone plug replacement

Before proceeding with the replacement of your cleaved headphone jack you lot demand to be familiar with the plug parts as this will involve connecting the right parts with the right cables then your headphone works perfectly without issues. Also to protect your headphone/multimedia device of being defected in any take a chance.

Annotation: If you're already familiar with the plug parts and types, or have enough confidence and experience you may skip this part directly to the headphone jack replacement steps below.

Headphone Jack Parts

Normally headphones divided into two categories mono headphones and stereo headphones, commonly near headphones in the market are stereo ones that come up with mobile phones, play station, iPods or any multimedia players cause those are serving average users like yourselves that willing to enjoy listening to high-quality stereo music in your headphones. On the other hand, at that place are certain cases where mono headphones are being used on certain devices or for studio purposes.

So in this regard, I want you lot to understand that if you have a normal commonly used stereo headphone you should run into that the jack has two black stripes dividing the jack into 3 metallic pieces (hence mono headphones will have only ane black stripe "metal ring").

Referring to the beneath image y'all can come across the departure between mono and stereo headphone plugs.

NOTE: I volition continue to evidence yous how to deal with the stereo headphone as this is the well-nigh common case hence the same applies for mono headphone plugs.

Stereo Headphone plug consists of 3 parts which are:

• Footing (Always represent the long stripe of the jack)
• Correct (always stand for the centre stripe of the jack)
• Left (always represent the tip strip of the jack)

Those parts correspond to 3 cables that are continued to the headphone speaker and this is what we gonna piece of work on to supersede the headphone jack after removing the damaged one.

Note: You might come across sometimes a headphone jack with 3 black stripe lines and iv metal parts, this commonly the case with headphones that have mic facility with it or some multimedia devices that utilise video along with the stereo audio.

Headphone Jack Replacement Steps

Step 1 – Cut the onetime headphone jack(this should take around 2 – 5 minutes)

• Outset, using the wire cutter cut the cable well-nigh the plug simply get out at least 2 cm cable to the plug cause nosotros will demand this next.
• By using the wire stripper remove around 2 to 3 cm from the headphone cable terminate.

NOTE: If yous exercise not have a wire stripper you could use normal scissors at abode by using it just like if y'all are about to cut the cable BUT utilize a very slight pressure just to catch the cable by the scissors then slide the pair of scissors out towards the end of the cable to strip it.

! Caution: Do not apply the scissors if yous feel yous cannot do it or you don't have the gut for it, I use information technology sometimes considering I have the feel and I did information technology earlier and then if you fail to do it properly you could cut the cables inside even without seeing a clear-cut. so better to have this into consideration.

• Remove coating from each smaller individual cable Green , Ruby-red , and Brownish cable using the same mentioned method higher up or past using a lighter by putting a flame of fire on each cable stop for a 2d to remove the colored plastic shield.

Cables color codes

• The Light-green  cable should connect to the Left speaker.
• Cerise connects to the Correct speaker.
• The Dark-brown cable to the Ground.

Annotation: If you sliced the cable and establish different colors on the 3 cables, you can employ AVO meter (multimeter) to check which cablevision connects to which metal ring of the jack only if you exercise not have a multimeter tool there should be at least a single Brown or Black cable which represents the basis (or common cable) so fixing the other 2 cables (for the Right and Left speakers) will not cause an issue since y'all fix the basis cable to the right jack terminal equally I volition evidence you below.

Stride ii – Connect the cables to the new plug y'all have (This should take no more than i – 2 minutes)

• Open the new headphone plug you have past screwing information technology, then put the second piece of the new plug into the cables you sliced (as shown in the below prototype) ↓Add – On Note
• The Brown cable should be connected to the big terminal of the new jack plug, just slide the Chocolate-brown cable into the big terminal pigsty every bit shown in the prototype and wrap it around the terminal for few times tightly.

• Solder the twisted Dark-brown cablevision on its place with the plug terminal and exist sure that it is fixed well and solid. (Check the below video and run across how I am soldering the dark-brown cable "ground" to the jack pole in )

Note: For a more than proper way to identify which plug terminal corresponded to which plug metallic section, nosotros should employ an AVO meter (or multimeter) and set information technology to ohms to check that perfectly, but since this is a very unproblematic easy tutorial on how to supplant a headphone plug I don't desire to make the procedure complex for average users.

Annotation: The Same concept of the higher up image can be used on the original damaged jack to determine which cable connected to which jack metal ring by touching the extra two cm cable by 1 of the multimeters cable pole (every bit shown in the above paradigm) and the other side touching the other multimeter pole.

• Insert the Green cable into the left terminal hole (consider it left if you place the new jack torso as shown in the below image) and wrap it around the concluding for few times tightly then solder it in its identify with the plug final and be sure that it is fixed well and solid.

• Echo the aforementioned terminal step with the Red cable by inserting information technology into the right console hole and wrap information technology effectually the last for few times tightly then solder information technology in its place with the new headphone plug terminal and be sure that it has soldered well and solid.

Annotation: If you desire to make sure that you have connected the right cables in their place (bold you haven't employ the AVO meter I mentioned in a higher place) and since you connected the Ruby-red and Dark-green cables tightly, just before soldering them you tin can brand a test by connecting the new socket plug into your multimedia device like an audio player or radio and check the speakers when yous switch the side controller right and left whether it is going in the correct sides like right goes to right and left goes to left during tuning the speaker sides…

! CAUTION: Remember that the iii cables should not touch on each other otherwise a short circuit will occur when y'all insert the plug into the jack or at least information technology will not piece of work properly.

Add – on Notation

You lot can do some other boosted step to make your piece of work perfect by using a Oestrus Shrink Sleeve past inserting a short piece of information technology within each of the iii colored cables, and after finalizing the soldering at the terminal phase simply push button those sleeves in a higher place all of the three soldered points individually (as shown in the below image) and so put some direct heat on them by using a lighter for an example till they shrink tightly on each of the cablevision/terminal connection.

By using the Heat Shrink Sleeves you lot are protecting the new headphone plug from existence corrupted over again in the future and preventing any accidental short circuit may occur at any fourth dimension due to daily usage of the headphone.

Conclusion

Ofttimes times one earpiece of the earphones stops working or having noise and cutting off the sound, most likely and common reasons behind this issue acquired past the headphone plug. So replacing the headphone plug yourself at dwelling could exist much easier than you look and since it doesn't worth wasting your time looking for a technician to make it happen for you, it is better to solve information technology out yourself within minutes in an like shooting fish in a barrel way post-obit How To Replace A Headphone Plug tutorial article.

Share this article from below if you believe people need to know almost it … 🙂

Firas Sameer

This is me Firas Sameer the one behind "How To Set Headphones" wearing my Beats headphone, I like listening to music a lot just since I had some issues with my headphone jack and I had to supplant it my self, I decided to create this website and assist you guys with headphone hacks all the way I am learning new ones and other stuff which helps you fix your ain.

Recent Posts

Source: https://howtofixheadphones.com/how-to-replace-a-headphone-jack-the-easy-way-solved/

Posted by: moodytheregoth.blogspot.com

Share this post